Accessories for Steam Bath

Fragrance dosing pump

Fragrance dosing pump with mounting material
Plastic housing, incl. dosing hose, nominal voltage 230 Volt, protection class IP65

Steam bath nozzles

• DDS22 Steam-bath-nozzle: Small steam bath nozzle for max. 4kg/h capacitv. For steam hose DS22 with Ø22 mm  
• DDL30 Steam-bath-nozzle from 4-32kg/h for DS22 steam hose with Ø30 mm
• DDL35 Steam-bath-nozzle from 4-32kg/h for DS35 steam hose with Ø35 mm

Steam nozzle sets

• Steam nozzle set W22 fits with steam hose DS22 Ø 22 mm
• Steam nozzle set W30 fits with steam hose DS60 Ø30 mm
• Steam nozzle set W35 fits with steam hose DS35 Ø35 mm
• Steam nozzle set W45 fits with steam hose DS80 Ø45 mm

Steam inlet

Steam inlet for the mixing and inserting of steam and fresh air into the steam room. For a dense steam appearance and
a lower temperature of the inserted steam:

• Mixing tube made of stainless steel V4A with connections for fresh air and steam
• Diameter 110 mm, Installation length 280 mm
• Cover made of stainless steel  V4A 140 x 140 mm with fixation screws

Dimensions:

Ø110 mm, installation length 280 mm

Cover 140 x 140  x 22,5 mm with fixing screws and mounting flange.  

Fan W2S130-AA 27-67

Special 3-stage insertion tube fan for Ø 150 mm.

Nominal Voltage: 24V 1~ 50Hz.

Current draw: /A  2.25/2.20A Power consumption: 40 Watt.  Speed / min-1 2760/3200

Type of protection: IP20

Multivent MV 100A 220-240V 50Hz 15W

Space saving tube fan. Suitable for supply and exhaust air.

Connection Ø 100 mm. Nominal voltage: 230V 50/60Hz. Output in V: m³/h  150/190

Type of protection: IP44

Electric regulator

Electric regulator 1A 230V 50Hz for surface mounting. Speed controller, Continuously adjustable

Backflow flap

Made of galvanised sheet steel DN100 for Ø100 mm

Temperature sensor

Temperature sensor with integrated safety temperature limiter (STB). The mounting kit for a wall thickness of 40 to 90
mm includes a M20 x 1.5 mm cable gland, threaded sleeve, two O-rings and a flat gasket.

Sensor type KTY81-110

TF: 76°C + 0/-10°C

Temperature sensor

Rod temperature sensor KTY81-110 for bench heating, Length: 42 mm x Ø 6 mm

Blind temperature sensor

Blind temperature sensor 6mm

Blind stainless steel V4A for temperature sensor with Ø 6 mm metal sleeve.

Approximately 3.5 cm outside diameter including grub screw for fixing the sensor element. Mounting hole of cabin lining
14 mm.

Mounting sleeve for coated GFK/Alu Surfaces:

Mounting hole 42 mm, mounting sleeve Ø 42 x 110 mm and nut, total length 113 mm (shortenable)

Mounting sleeve for surfaces to be tiled:

For tiled wet rooms / steam baths

Mounting hole 42 mm, mounting sleeve Ø 42 x 110 mm and nut, total length 113 mm (shortenable) with sealing flange and



6 screws for fixation  

LED spot warm white

Built-in lamp VA chromed Type of protection: IP 65; LED warm white 1 Watt; Linse matt;  Lense frosted; Cover Ø60 mm

Incl. connecting cable 20 cm; Plug type: JST

LED RGB Spot

Built-in lamp VA chromed Type of protection: IP 65 ; LED-RGB  3×1 Watt; Lense frosted; Cover Ø60 mm

Incl. connecting cable 20 cm; Plug type: JST

Push button red

Piezo push button with red ring illumination 24VDC

Installed in holder/ cover screen innox. Chrome plated 60 mm outer diameter; 7 m wire 5 x 0.25 mm² with connector.


For installation in mounting sleeve Ø42 mm; Connection wire JST. The button is also available in
blue

Controller LED warm white

For max. 1-12 pcs. 1W spots. 1 x converter 350mA LCM-40 constant current.

Incl. poti for dimming on housing

Power supply cable 2m white, 230V/AC – 1,1A 7 m cable to spot 1 JST + end plug

Controller LED RGB

15 different light programmes can be choosen by a code switch

Synchronous colour gradient.

Dimmable via poti on housing

Output RGB-LED Spot 350 mA 1-10

Power supply 230 VAC with plug 230 VAC 1 Ph 50Hz 50W; 7 m cable to spot 1 JST + end plug

Push-button plates:

Dibond button plates with illuminated piezo push-button:

Plates optionally with 1 – 4 piezo buttons; blue ring illumination and indentation for name tags:

7 m cable and screws M4x30

Push-button housing:

Flush-mounted housing for installing the push-button panels in building boards, dry- or masonry walls. Material: polystyrene
(PS), black. Supplied with a protective cover made of EPS to define a clear tile edge and to protect against contamination
of the interior

Mounting material

An overview of our installation material and detailed information can be found in our brochure

„Accessories Wellness“

Spa Control Delta

External Touch Display

Optionally a remote touch display can be connected to the Omega steam generator.

It is available as flush-mounted or wall-mounted version, with only 19-mm wall oustanding. You have the choice from three standard frames: brushed stainless steel, white or black glass. There are two different display layouts matching to the selected cover.

The cleverly designed magnetic frame construction, however, also allows steam bath builders to individualize the fitting with a material of the customer’s liking. A waterproof installation of the display is possible.